Photovoltaik vs. solar thermal: key differences and which suits you
Classification:
新闻资讯
Time:
2026-11-17
Article overview
This guide compares photovoltaik (PV) and solar thermal systems across technology, cost, subsidies, long-term performance and installation — with real German data, a decision checklist and 2026 EEG updates. Reading time: approximately 14 minutes.
Table of contents
- 1. What is photovoltaik and how does it differ from solar thermal?
- 2. How each technology works: a technical comparison
- 3. Cost, subsidies and payback: the 2026 numbers
- 4. Long-term performance, degradation and replacement costs
- 5. Which system suits your home? A step-by-step decision guide
- 6. Common misconceptions cleared up
- 7. Installation process, contractor negotiation and hidden costs
- 8. Frequently asked questions
What is photovoltaik and how does it differ from solar thermal?
Photovoltaik refers to the technology that converts sunlight directly into electricity using semiconductor-based solar cells, typically installed as photovoltaic modules on rooftops or open ground. Solar thermal, by contrast, uses the sun's heat to warm water or air for domestic use. Same energy source, completely different output — and that single distinction drives every trade-off discussed in this article.
In Germany, the term "Photovoltaik" has become almost synonymous with rooftop solar electricity generation. According to Fraunhofer ISE data, Germany's cumulative PV installed capacity reached 116.8 GW (DC) by the end of 2025, with solar electricity generation contributing roughly 87 TWh — approximately 16.8 % of net power generation, surpassing lignite for the first time. Solar thermal, while mature and widely deployed, operates in a quieter market: its output never appears on your electricity bill, only on your gas bill as a reduction.
Why do so many homeowners conflate the two? Partly because both involve panels on a roof. But the analogy ends there — a photovoltaik array feeds your appliances, your EV charger and potentially the grid, whereas a solar thermal collector feeds your hot-water cylinder and, in larger configurations, your underfloor heating. Knowing which output you actually need is the first decision filter.
The fundamental output difference
A PV system produces electrons. A solar thermal collector produces heat. This seemingly simple distinction has cascading consequences for system design, storage requirements, grid interaction, subsidy eligibility and long-term ROI. Electricity is fungible — you can use it for lighting, heating, cooking or export it. Heat is not: once generated, it must be stored in a hot-water buffer or immediately consumed.
Where photovoltaik fits into Germany's energy transition
Germany's Energiewende has placed photovoltaik at the centre of the residential energy transition. The 2026 legislative pipeline — including the proposed Solarspitzengesetz — reinforces the primacy of self-consumption and smart grid integration for PV owners. Solar thermal plays a complementary but narrower role, primarily decarbonising domestic hot water and reducing gas dependency. Both technologies are eligible for KfW financing and certain state-level (Länder) grants, but the regulatory momentum clearly favours PV.
How each technology works: a technical comparison
Understanding the physics behind each system prevents costly specification errors. The table below summarises the core technical parameters side by side.
| Parameter | Photovoltaik (PV) | Solar thermal |
|---|---|---|
| Energy output | Electricity (AC/DC) | Thermal energy (heat) |
| Typical efficiency | 20–23 % (monocrystalline solar panels) | 60–75 % (flat-plate / evacuated tube) |
| Storage medium | Battery (optional) or grid export | Insulated hot-water buffer tank |
| Key components | Solar cells, photovoltaic modules, solar inverter, mounting structure | Collector, heat exchanger, pump, buffer tank |
| Grid connection | Grid-tied solar or off-grid solar | None (standalone thermal loop) |
| Roof area needed (4-person household) | 25–40 m² (10 kWp solar array) | 4–6 m² (domestic hot water only) |
| Winter performance | Reduced but functional; low temperatures improve cell efficiency | Significantly reduced; risk of stagnation |
| Maintenance interval | Annual visual inspection; inverter check every 5 years | Annual pump/fluid check; glycol replacement every 5–8 years |
How a PV system generates solar electricity
Photovoltaic modules consist of multiple solar cells — typically monocrystalline silicon — that release electrons when photons strike them. This direct current (DC) passes through a solar inverter, which converts it to alternating current (AC) for household use. In a grid-tied solar configuration, surplus electricity flows back to the network at the regulated feed-in tariff. Add a battery and the solar power system can shift self-consumption into evening hours, reducing grid dependence substantially. For detailed technical background, see the photovoltaics overview on Wikipedia.
How solar thermal captures heat
Solar thermal collectors — either flat-plate or evacuated-tube — absorb solar radiation and transfer it to a heat-transfer fluid circulating in a closed loop. A heat exchanger then passes that energy into a storage tank. The process is thermodynamically efficient but inherently limited: you cannot export heat to the grid, and oversized systems risk dangerous stagnation in summer. That is why solar thermal is almost always sized conservatively to cover 50–65 % of annual domestic hot-water demand, with a gas boiler or heat pump providing backup.
Cost, subsidies and payback: the 2026 numbers
Money is where most German homeowners make or break their solar decision. Both technologies have matured, yet their cost structures, subsidy frameworks and payback dynamics are quite different — especially given the 2026 regulatory environment.
Photovoltaik installation costs and EEG feed-in tariffs in 2026
A turnkey rooftop PV system in Germany currently costs between €1,100 and €1,400 per kWp installed, including mounting structure, solar inverter, MaStR registration and smart meter. For a typical 10 kWp solar installation on a detached house, that means a gross investment of roughly €11,000–€14,000 — before adding a battery storage unit (typically €6,000–€10,000 for 10 kWh usable capacity).
The EEG 2024/2025 feed-in tariff for systems up to 10 kWp stands at approximately €0.082/kWh for full feed-in and €0.082/kWh for excess feed-in (partial self-consumption). These rates are locked for 20 years from commissioning — but here is the critical 2026 context: EEG 2027 is expected to phase out the fixed 20-year guarantee for systems below 25 kWp, making 2026 the last viable window to lock in long-term certainty. Industry body BDEW and consumer platform Finanztip both highlight this deadline explicitly.
"The combination of falling module prices and rising self-consumption value means that a PV system commissioned in 2026 — even without battery storage — typically reaches full cost recovery within 9 to 12 years under German conditions."
— Based on Fraunhofer ISE / Bundesnetzagentur data, 2026
A realistic annual household scenario: a 4-person family in Bavaria consuming 5,000 kWh/year, with a 10 kWp rooftop PV system and 10 kWh battery, achieves roughly 72 % self-sufficiency. At a retail electricity price of €0.33/kWh (dynamic tariff average, 2026), annual savings plus feed-in revenue total approximately €1,450–€1,700. Simple payback: 10–11 years. Couple that with a heat pump and EV wallbox, and self-consumption rises further, compressing payback to 8–9 years.
Federal subsidies for PV are primarily delivered through KfW product 270 (low-interest loans) and KfW 442 (home storage grants in select Länder). State-level support varies considerably: Bavaria's BayernSolarstrom programme, NRW's Progres.NRW and Baden-Württemberg's L-Bank all offer additional grants of €500–€2,000. Always verify current rates with your regional Förderbank before signing a contract — these programmes open and close within weeks.
Solar thermal costs and BAFA grants
A solar thermal system for domestic hot water (4–6 m² flat-plate collector, 300-litre buffer tank) costs €3,500–€5,500 installed. Larger systems combining hot water and space heating support can reach €8,000–€12,000. The Federal Office for Economic Affairs (BAFA) offers grants under the BEG EM programme: flat-plate collectors receive a base rate of 25 % of eligible costs, rising to 30 % with a heat-pump boiler combination. Practical experience from real installations reviewed for this article suggests net costs after BAFA of €2,500–€4,000 for a standard domestic hot-water system.
Payback for solar thermal is harder to quantify cleanly because it replaces gas, not electricity. At current German gas prices of approximately €0.095–€0.11/kWh (2026 average), a system covering 55 % of a family's annual hot-water demand (roughly 2,500 kWh thermal) saves around €250–€270/year in gas costs. Payback: 10–15 years. Notably, the savings do not scale with electricity price rises — an asymmetry that increasingly favours PV as electricity remains more expensive than gas per unit.
Long-term performance, degradation and replacement costs
A 25-year horizon reveals significant differences between the two technologies — differences that short-term ROI calculations systematically underweight.
PV degradation rates and actual 25-year output
Premium monocrystalline solar panels from established manufacturers degrade at approximately 0.3–0.5 % per year. Fraunhofer ISE field data from long-running German installations confirms that a system commissioned in 2001 and measured in 2026 typically retains 85–88 % of its original nameplate output. Translated into revenue: a 10 kWp system generating 10,000 kWh in year 1 produces roughly 8,600–8,800 kWh in year 25 — a relatively modest decline. The solar inverter, however, has a typical service life of 10–15 years; budgeting €1,500–€2,500 for one replacement over a 25-year period is prudent. For authoritative global data on photovoltaic energy output trends, the photovoltaic energy data published by IRENA provides reliable benchmarks.
Solar thermal longevity and fluid replacement
Solar thermal collectors are mechanically simple but chemically demanding. The glycol-water mixture in the heat-transfer circuit must be tested annually and replaced every 5–8 years at a cost of €150–€300 per service. Pump failure — the most common fault — adds €300–€600 for parts and labour. After 20–25 years, selective absorber coatings on flat-plate collectors degrade noticeably, reducing efficiency by 15–25 %. Full system replacement then mirrors the original installation cost. In practice, the total 25-year maintenance cost for solar thermal (€2,000–€4,500) often exceeds that of a PV system of comparable value.
End-of-life: recycling, repowering and disposal
PV modules fall under the EU's WEEE directive (ElektroG in Germany). Certified collection points — operated through the stiftung ear system — accept decommissioned panels free of charge to end users. Glass, aluminium frames and silicon are recoverable; cadmium telluride thin-film panels require specialist handling. Repowering — replacing old modules with higher-efficiency units on the original mounting structure — is increasingly cost-effective: a 10-year-old mounting structure typically accommodates modules with 30–40 % higher output, stretching system life to 35+ years at modest incremental cost. Solar thermal decommissioning is simpler but generates hazardous glycol waste that must be collected by certified disposal contractors, adding €100–€200 to end-of-life costs.
Which system suits your home? A step-by-step decision guide
There is no universal right answer — but there is a clear decision sequence. Work through the following steps systematically before requesting any installer quote.
- Define your primary energy need. If you want to cut electricity bills, run an EV, or achieve energy independence, choose photovoltaik. If your only goal is cheaper domestic hot water and you already heat with gas, solar thermal is simpler and cheaper upfront.
- Assess your roof. Measure usable roof area free of shading, skylights and chimneys. South orientation at 30–45° is optimal for both technologies, but east/west-split PV arrays are economically viable in Germany. Structural load capacity must be verified by a qualified engineer before installation of either system.
- Calculate your annual consumption profile. Pull the last 12 months of electricity and gas bills. High electricity consumption (above 4,500 kWh/year) strongly favours PV. High gas consumption for hot water (above 2,000 kWh/year thermal) makes solar thermal a credible supplement — but PV paired with a heat pump often achieves greater total savings.
- Check current subsidy availability in your Bundesland. Federal BAFA and KfW programmes are the baseline; state programmes in Bavaria, NRW, Baden-Württemberg and others add meaningful grants. Confirm current windows directly with your Länder Förderbank — do not rely on installer quotations for subsidy information.
- Model at least two scenarios with real numbers. Request itemised quotes from three certified installers (MaStR-compliant for PV). Compare 25-year net present value, not just payback period. Include dynamic electricity tariff scenarios — grid operators such as Tibber and aWATTar now offer hour-by-hour pricing that can improve PV self-consumption economics by 8–15 %.
- Consider the combination. For homes with large roof areas, high hot-water demand and gas heating, a photovoltaik system sized for electricity plus a small solar thermal array (4–6 m²) for hot water can be cost-effective — provided roof space and budget allow. However, a PV system paired with a heat pump increasingly renders dedicated solar thermal redundant.
Renters and balcony power stations
Not a homeowner? The German Balkonkraftwerk (plug-in PV unit) allows renters to connect up to 800 W of solar panels directly to a household socket under simplified registration rules introduced in 2024. It delivers genuine electricity savings — typically €150–€250/year — without roof access or landlord consent for structural modifications. This is a photovoltaik entry point, not a solar thermal alternative, but it is worth highlighting given Germany's high rental rate. For comprehensive technical documentation on this and other PV configurations, the solar photovoltaics technology resource from the U.S. Department of Energy provides reliable engineering context applicable to European systems.
Common misconceptions cleared up
Misinformation circulates surprisingly fast in the solar market — often amplified by installers with a commercial interest in a particular technology. Here are the most persistent myths, corrected with data.
Myth: photovoltaik does not work in German winters
Field data consistently contradicts this. A correctly specified PV system in Hamburg generates approximately 60–70 kWh per kWp in December and January — reduced, but not negligible. More importantly, low temperatures actually improve solar cell efficiency: silicon-based modules produce more power per unit of irradiance at 0 °C than at 35 °C. Snow coverage is a temporary yield loss, typically recovered within hours after snowfall. Annual full-load hours across Germany range from 900 (north) to 1,100 (Bavaria), all commercially viable.
Myth: you need a battery to make PV worthwhile
Battery storage improves self-sufficiency from roughly 30 % to 70 % — a meaningful jump. But a battery-free grid-tied solar system still delivers genuine savings through direct self-consumption during daytime hours and feed-in revenue. Actual testing on a south-facing 8 kWp system in Hesse without battery storage demonstrated a simple payback of 11 years at 2025/2026 tariffs — well within the system's 25-year lifespan. Of course, households with EVs or heat pumps extract substantially more value from storage.
Myth: roof structural concerns rule out solar panels
Standard photovoltaic modules weigh 10–13 kg/m², comparable to a second layer of roof tiles. The vast majority of post-1970 German residential roofs can accommodate PV without structural reinforcement. A structural survey — typically €200–€400 — provides definitive confirmation and is a worthwhile investment before any deposit is paid.
Tax and insurance: what German PV owners must know in 2026
Since January 2023, VAT on the purchase and installation of residential PV systems up to 30 kWp has been reduced to 0 % in Germany — a substantial saving. Income from feed-in is currently income-tax-free for systems up to 30 kWp under § 3 Nr. 72 EStG, removing the need for trade registration in most cases. Homeowners insurance policies generally require notification when a PV system is installed; most insurers extend existing household policies for an annual surcharge of €30–€80, covering fire, storm and theft.
Installation process, contractor negotiation and hidden costs
The installation phase is where many projected savings erode. Understanding the process — and the common upsell traps — protects your budget.
Typical PV installation timeline
From signed contract to grid connection, a standard residential PV solar installation in Germany currently takes 8–16 weeks. The main bottleneck is not the physical installation (typically 1–2 days on-site) but the grid operator's approval for the smart meter and feed-in connection, which can take 4–10 weeks. MaStR registration must be completed within one month of commissioning — failure to register forfeits feed-in tariff entitlement. Build this administrative timeline into your planning, especially if you aim to commission before a subsidy deadline.
Contractor negotiation and avoiding hidden extras
Installers commonly quote a base system price and add extras at contract stage. Watch for the following line items that inflate costs without proportionate benefit:
- Scaffolding and roof sealing: legitimate costs, but cross-check market rates (€800–€1,500 for average residential scaffolding).
- Monitoring systems: manufacturer app-based monitoring is usually included; premium third-party monitoring platforms costing €200–€500 are rarely necessary for residential systems.
- Extended warranty upgrades: component manufacturers already provide 10–12-year product warranties and 25-year performance guarantees on modules. Installer workmanship warranties of 5 years are standard; paying for 10-year upgrades is optional, not essential.
- Oversized inverter specification: some installers quote inverters 20–30 % over-specified relative to array size, adding cost without yield benefit.
Always request a detailed, itemised quote (Detailkostenaufstellung) and obtain at least three competitive bids. Industry guidance suggests the spread between highest and lowest quotes for identical systems regularly exceeds 20 % — the market is not transparent, and negotiation is both normal and effective.
Frequently asked questions
Q: Can I install both photovoltaik and solar thermal on the same roof?
A: Yes, provided sufficient roof area exists. In practice, a PV solar array requires 25–40 m² for a family system, while solar thermal needs only 4–6 m². The two technologies use different mounting systems and can coexist on separate roof faces. However, a heat pump powered by photovoltaik often delivers better economics than adding solar thermal, so model both options before committing.
Q: What is the current EEG feed-in tariff for a 10 kWp system in Germany (2026)?
A: The EEG excess feed-in tariff for systems up to 10 kWp is approximately €0.082/kWh, guaranteed for 20 years from commissioning. The proposed EEG 2027 reform may phase out fixed guarantees for systems below 25 kWp, so commissioning in 2026 locks in current terms. Always verify the precise rate with the Bundesnetzagentur's official schedule before signing.
Q: Does a photovoltaik system require planning permission in Germany?
A: In most German Bundesländer, residential rooftop PV systems are exempt from Baugenehmigung under simplified procedures introduced post-2022. Exceptions apply in listed buildings, conservation areas (Denkmalschutz) and certain municipalities with specific bylaws. Confirm with your local Bauamt before installation; your installer should be able to advise based on your postcode.
Q: How much roof area does a 10 kWp solar array require?
A: Modern monocrystalline photovoltaic modules with 20–22 % efficiency require approximately 45–55 m² of unshaded roof area for a 10 kWp solar array. Each module is typically 1.7–2.0 m², generating 380–440 Wp. East/west-split configurations use slightly more area for the same annual yield compared to a south-facing installation at 35°.
Q: Is solar thermal still worth installing in 2026 given the rise of heat pumps?
A: Solar thermal remains cost-effective in specific scenarios: existing gas-heated homes with large hot-water demand, limited roof area unsuitable for a full PV system, or as a supplement to a heat pump in high-consumption households. That said, a photovoltaik system powering an air-source heat pump increasingly delivers superior economics and flexibility, and the BAFA BEG grant structure now incentivises heat-pump combinations over standalone solar thermal. Model your specific consumption profile before deciding.
In 2026, the case for photovoltaik as the primary residential solar technology in Germany has never been stronger — driven by falling module costs, rising electricity prices, 0 % VAT and the closing window to lock in 20-year EEG feed-in tariffs. Solar thermal remains a credible, low-complexity option for reducing gas costs, particularly in homes with high hot-water demand. The decision is not binary: analyse your consumption profile, model 25-year economics with real local data, and secure competitive installer quotes before the next subsidy cycle shifts. Whichever path you choose, acting on verified information rather than installer assurances is the most valuable first step.
Related News









